Fittings 62 to 66
Type 62 - Standard Railing Flange
62.jpg (18055 bytes)

Tube Reference

mm

Bolt Hole

Kg

Type

A

B

C

D

E

F

G

H

Diameter

62-2

2

32

64

44

39

5

9

0.04

62-5

5

65

116

79

76

6

11

0.59

62-6

6

76

128

89

89

8

14

0.73

62-7

7

76

140

90

102

11

14

1.30

62-8

8

89

155

90

115

12

14

1.60

62-9

9

102

165

127

127

10

18

1.76

 

Ideal when a structural fixing is required. Type 62 should always be used to fix down guardrailing and balustrades. The holes are of sufficient diameter to give a good fixing with either a mechanical or chemical anchor, and the two socket set screws in the vertical socket give greater stability to the upright. It is recommended that the fixing holes in the flanges should be inline with the applied load.

Note: The Type 62-7 and Type 62-8 fittings have been especially designed to comply with the 100mm sphere rule as defined in BS 6180 and Building Regulations, in the design of balustrade systems.

 


Type 63 - Angle Base Flange
63.jpg (18055 bytes)

Tube Reference

mm

Bolt Hole

Kg

Type

A

B

C

D

E

F

G

H

Diameter

63-6

6

78

130

92

96

8

14

0.98

 

This fitting is similar to Type 62, but is used to set up the upright at an angle between 45 and 65 degrees. Only available in size 6. This fitting should only be subjected to light loads due to its size and the base fixing holes, which cannot be positioned at 90 degrees to the applied load. For greater loads or other tube sizes, Type 62 flange is used and the upright bent to the required angle.
 

Type 64 - Standard Vertical Railing Base
64.jpg (18055 bytes)

Tube Reference

mm

Bolt Hole

Kg

Type

A

B

C

D

E

F

G

H

Diameter

64-6

6

87

95

21

67

57

14

0.77

64-7

7

92

108

22

72

64

14

1.12

64-8

8

99

122

22

89

70

14

1.54

 

This fitting is designed for palm fixing guardrailing and balustrading to walls, parapets, steps, and ramps.
The upright cannot drop through the socket.

Note: Should an upright be required to pass through the fittings, the base can be bored out to order.
Also, access to the top fixing hole is restricted by the position of the flange to the barrel.
When selecting a hexagon head bolt or similar bolt fixing, the maximum length of the bolt including the head must not exceed 25mm.

 


Type 65 - Standard Horizontal Railing Base
65.jpg (18055 bytes)

Tube Reference

mm

Bolt Hole

Kg

Type

A

B

C

D

E

F

G

H

Diameter

65-6

6

83

98

22

67

57

14

0.76

 

This fitting is designed for palm fixing guardrailing and balustrading to walls, parapets, steps, and ramps. Only available in size 6.
The upright cannot drop through the socket.

Note: Should an upright be required to pass through the fittings, the base can be bored out to order.

 


Type 66 - Ground Socket
66.jpg (18055 bytes)

Tube Reference

mm

Bolt Hole

Kg

Type

A

B

C

D

E

F

G

H

Diameter

66-6

6

127

123



1.87

66-7

7

140

136



2.32

66-8

8

140

136



2.50

 

A ground socket fitting for use when uprights are required to be removable. It incorporates a socket set screw fixing and can be supplied with a plug to fill the hole when the tube is removed.
 

1 , 2 , 3 , 4 , 5 , 6 , 7 , 8 , 9 , 10 , 11 , 12 , 13 , 14 , 15
 
Return to the Fittings Catalogue